Search all content

Current document versions only

1 - 10 of 14 results

AS/NZS 1596:2014 The storage and handling of LP Gas 2014 cover

Name

AS/NZS 1596:2014 The storage and handling of LP Gas

Publisher

Standards Australia/Standards New Zealand

Version: Fourth Edition 2014. (Current)

Sets out requirements and recommendations for the safe storage and handling of LP Gas, in cylinders and bulk tanks.

8 results

found in this document show

Page 9

… AUSTRALIA/STANDARDS NEW ZEALAND Australian/New Zealand Standard The storage and handling of LP Gas SECTI ON 1 SCOPE AND GENERAL 1.1 SCOPE AND OBJECTIVE This Standard specifies … series. (g) Land transport equipment and operations, as covered— (i) in Australia, by the ADG Code (but excluding references to this Standard that appear in the ADG Code) and AS 2809, Parts … Hazardous Substances (Tank Wagons and Transportable Containers) Regulations 2004. The Code of Practice HSNOCOP 29, Flammable Gases and Oxygen Tank Wagons—A code of practice for the design …

Page 22

… Transfer Notice and amendments. 1.4.61 Tanker A road tank vehicle that meets the requirements of AS 2809.1 and AS 2809.3, or with earlier Standards superseded by AS 2809.3, or with the New Zealand Environmental Protection Authority (EPA) Approved Code of Practice for ‘Flammable Gases and Oxygen Tank Wagons’. 1.4.62 Thermal screen A wall or other …

Page 31

… 29 SECTI ON 4 CYLINDE RS AND SYSTE M S AS/NZS 1596:2014 CYL I NDER 4.1 SCOPE AND APPLICATION OF SECTION This Section provides requirements and recommendations for the location, design and … cylinders shall conform with the New Zealand Environmental Protection Authority (EPA) Approved Code of Practice, In-situ Filling of LPG Cylinders, available from the Liquefied Petroleum Gas …

Page 41

… 1596:2014 4.4.12 Additional requirements for cylinders for in situ filling An installation of cylinders intended for in situ filling shall comply with the following requirements: (a) … cylinders shall conform to the New Zealand Environmental Protection Authority (EPA) Approved Code of Practice HSNOCOP 38, ‘In-situ Filling of LPG Cylinders’ available from the LPGA. 4.5 CYLINDER …

Page 87

… 85 AS/NZS 1596:2014 SECTI ON 9 CYLINDE R FILLING INSTALLATI ONS  NE W ZEAL AND 9.1 SCOPE OF SECTION This Section provides requirements for installations for the filling of cylinders … or (b) A cylinder mounted on any other type of vehicle; or (c) A cylinder operating under a code of practice approved by the New Zealand Environmental Protection Authority (EPA) relating to …

Page 105

… 103 SECTI ON 11 AS/NZS 1596:2014 OPE RATIONS 11.1 SCOPE OF SECTION This Section sets out procedures for the operation and upkeep of an LP Gas … Requirements Where LP Gas is to be transported, handled, or stored, the requirements of the ADG Code/The New Zealand Land Transport Rule Dangerous Goods and this Section shall be satisfied. … NZS 5263:2003 (Gas detection and odourization); or (b) odourized in accordance with a code of practice approved by the authority. 4 The possibility of odour fade should be considered …

Page 131

… 129 AS/NZS 1596:2014 AS/NZS A1 2832 2832.1 Cathodic protection of metals Part 1: Pipes and cables 2865 3000 Safe working in a confined space Electrical … Transport of dangerous goods on land 5435 Specification for liquefied petroleum gas (LPG) 5807 Code of practice for industrial identification by colour, wording or other coding NZS/AS 1657 NZS/BS 750 …

Page 133

… 131 AS/NZS 1596:2014 US DEPARTMENT OF TRANSPORTATION Hazardous Materials Regulations NEW ZEALAND Statutes Hazardous Substances and … Transportable Containers) Regulations 2004 Land Transport Rule: Dangerous Goods 2005 Approved Codes of Practice HSNOCOP 29—Flammable Gases and Oxygen Tank Wagons LPG Compliance 100 kg to 300 kg …

AS/NZS IEC 60079.10.1:2022 Explosive atmospheres, Part 10.1: Classification of areas - Explosive gas atmospheres 2022 cover

Name

AS/NZS IEC 60079.10.1:2022 Explosive atmospheres, Part 10.1: Classification of areas - Explosive gas atmospheres

Publisher

Standards Australia/Standards New Zealand

Version: First Edition 2022. (Current)

AS/NZS IEC 60079.10.1:2022 adopts IEC 60079 10 1:2020, which specify requirements for the classification of areas where flammable gas or vapour hazards may arise and may then be used as a basis to support the proper design, construction, operation and maintenance of equipment for use in hazardous areas.

6 results

found in this document show

Page 21

… IEC 60079-10-1:2020 © IEC 2020 – 17 – AS/NZS IEC 60079.10.1:2022 In the case of activities other than those of normal operation, e.g. commissioning or nonroutine … controls as possible according to the current state of the art and in accordance with relevant codes and standards. This document provides guidance on aspects that should be considered and the classification of hazardous areas requires the application of good engineering practice. 4.2 Hazardous area classification objectives Hazardous area classification is a method …

Page 24

… before plant start-up. Consideration should always be given to the type, number and location of various potential points of release so that relevant zone and boundary conditions are … of the particular factors involved. Such factors could include: levels of cleanliness, industry practice, competency and training of personnel handling the flammable substances, other spill or … to applications such as laboratories, small refrigerant systems or cylinders of NOTE 2 Industry codes commonly identify quantities below which the hazardous area classification process would …

Page 90

… – 86 – IEC 60079-10-1:2020 © IEC 2020 Figure E.12 – Hazardous distance (Example No. 5) Extent of zone (see Figure E.12, r extent of zone is approximately 1,0 m due to surrounding … details may vary depending on the specific installation details or application of the relevant code of practice. This example has been taken because it contains a variety of forms of release which …

Page 114

… AS/NZS IEC 60079.10.1:2022 Country or Region of Origin – 110 – Code or Standard Designation TRGS 510 Title Lagerung von Gefahrstoffen in … gas explosion hazard, based on NEN-ENIEC 60079-10-1 UK EI15 Energy Institute Model code of safe practice for the petroleum industry, Part 15: Area Classification Code for Petroleum …

Page 115

… IEC 60079-10-1:2020 © IEC 2020 Country or Region of Origin Code or Standard Designation NFPA 497 AS/NZS IEC 60079.10.1:2022 – 111 – Title Developing Body Application Notes National Fire Recommended Protection Practice for the Classification of Association Flammable Liquids, Gases, or Vapours and of …

Page 116

… – IEC 60079-10-1:2020 © IEC 2020 Bibliography [1] A.W. Cox; F.P. Lee & M.L. Ang; Classification of Hazardous Locations, Ichem, 1993 [2] IGEM/SR/25; Hazardous Area Classification of Natural Gas … of High Flashpoint Liquid Fuels. Int. Symposium on Combustion [13] The Energy Institute, Model Code of Safe Practice – Part 15 – Area Classification Code for Installations Handling Flammable Fluids; 4 th …

AS 1375:2023 Industrial fuel-fired appliances 2023 cover

Name

AS 1375:2023 Industrial fuel-fired appliances

Publisher

Standards Australia

Version: Fourth Edition 2023. (Current)

Specifies requirements and safety principles for the design, installation and operation of industrial appliances that involve the combustion of gas or liquid fuel and the controlled generation of combustible vapours or combustible dusts.

9 results

found in this document show

Page 13

… covering systems and devices for the production, storage, transport, measurement and use of hydrogen. While this work has been primarily focused on the use of hydrogen in vehicles, the … standards for hydrogen have also been part of this work. To help develop and implement safe practices in North America, the Hydrogen Safety Panel was established in 2003 to support the US … for additional information on hydrogen initiatives. In Queensland in 2022, a Hydrogen Safety Code of Practice was released by the Petroleum and Gas Inspectorate. © Standards Australia …

Page 61

… operation Installation requirements All necessary licences, approvals and other required forms of authorization should be checked and in order before commencing an installation. NOTE Responsibilities may be assigned by legislation, regulations or codes (e.g. state or national work health and safety legislation) or be included in a … condition by isolating or disconnecting the supplies. 5.2 Standards for workmanship and good practice 5.2.1 Materials Any material used in the installation of an appliance shall be in …

Page 95

… Gas Council Research Communication GC147 (Ref. [3]) which developed the basis for safe ignition of industrial burners using the energy release criterion, now known as Case A. The calculations … criterion and appliance strength rationale was subsequently adopted in the British Gas burner codes of practice. Hence unless it is known that the appliance or its combustion chamber is extremely …

Page 96

… AS 1375:2023 82 The effect on pressure rise of venting through appliance flues and other openings was also examined. While simple orifices … [23]) on resolving the use of dilution to ensure safe starting of burners resulted in a new code of practice for large gas and dual fuel burners (Ref. [7]), published in 1976 prior to the release …

Page 101

… variability. Also, depending on the experimental configuration, the ignition temperature of a fuel gas from a hot surface is typically much higher than the AIT. From the experiments in … of a poor mixing burner. These values were adopted as the gas burner start-up criteria in the Code of Practice for Large Gas and Dual Fuel Burners (Ref. [7]) and Standards for Automatic Gas Burners …

Page 170

… for completing that action is recorded on the record sheet. As actions are completed, the sign-off is recorded on the original record sheet. It is usual to record each step of a HAZOP for all … there are novel hazards associated with the operation; to justify adherence to a particular code of practice, guidance note or industry code. © Standards Australia Limited 2023 …

Page 207

… document. It specifically states that any new, novel or alternative materials, designs, methods of assembly, procedures, etc. which do not conform with a specific requirement of this document … The evidence and analysis is expected to use published research, recognized standards, codes of practice and industry guides where applicable. In-house procedures, specifications, guides and …

Page 209

… to the fitness-for-purpose assessment. Evaluation documentation typically includes sufficient of the following to establish fitness-for-purpose for the owner or operator or both, and the … of the clause by clause assessment where there is a comparison or use of other standards, codes of practice, guides or specifications rather than using this document. (b) (d) Any independent …

Page 250

… AS 1375:2023 236 IGEM/SR/25, Hazardous area classification of Natural Gas Installations NFPA 2, Hydrogen Technologies Code NFPA 67, Guide on Explosion Protection for Gaseous Mixtures in Pipe Systems NFPA 68, … NO2 in promoting methane oxidation. Proc. Combust. Inst. 2011, 33 (1) pp. 441–447 [7] Code of practice for large gas and dual fuel burners. British Gas Report IM/7 1976 [9] Coward H.F and …

AS/NZS 5139:2019 Electrical installations - Safety of battery systems for use with power conversion equipment 2019 cover

Name

AS/NZS 5139:2019 Electrical installations - Safety of battery systems for use with power conversion equipment

Publisher

Standards Australia/Standards New Zealand

Version: First Edition 2019. (Current)

Specifies requirements for general installation and safety requirements for battery energy storage systems (BESSs), where the battery system is installed in a location, such as a dedicated enclosure or room, and is connected with power conversion equipment (PCE) to supply electric power to other parts of an electrical installation.

2 results

found in this document show

Page 10

… AS/NZS 5139:2019 2 NOTE 1 While this Standard applies to systems of up to 200 kWh, the general requirements of this Standard may apply to larger installations. … storage systems (BESSs) — in Section 4. (c) Battery systems and BESSs not conforming to Best Practice Guide: battery storage equipment — Electrical Safety Requirements — in Section 6. (b) … in conjunction with the AS/NZS 4509 series. Local government, Australian National Construction Code (NCC) and New Zealand Building Code requirements for buildings may also apply where a BESS …

Page 11

… the Australian/New Zealand Wiring Rules) AS/NZS 3008.1.1, Electrical installations — Selection of cables, Part 1.1: Cables for alternating voltages up to and including 0.6/1 kV — Typical … systems of fuses A to F IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 60896, Stationary lead-acid batteries (series) IEC 62109‑1, Safety of power converters … rating of 1,5 kV DC NZS 4219, Seismic performance of engineering systems in buildings Best Practice Guide: battery storage equipment — Electrical Safety Requirements, V 1.0 (2018)1) 1) …

AS/NZS 3000:2018 Electrical installations (known as the Australian/New Zealand Wiring Rules) 2018 cover

Name

AS/NZS 3000:2018 Electrical installations (known as the Australian/New Zealand Wiring Rules)

Publisher

Standards Australia/Standards New Zealand

Version: Third Edition 2018. (Current)

AS NZS 3000 2018 (known as the Australian/New Zealand Wiring Rules) specifies requirements for the design, construction and verification of electrical installations, including the selection and installation of electrical equipment forming part of such electrical installations; part 1 provides provisions that constitute the minimum regulatory requirements for a safe electrical installation; part 2 provides work methods and installation practices that are ‘deemed to comply’ with the requirements of Part 1.

3 results

found in this document show

Page 174

… 171 (b) Where a suitable screen of a multi-core cable is used as a protective earthing conductor, it shall be acceptable to … to current and superseded Australian and New Zealand Standards and typical European practices. Figures 3.2 demonstrates the coordination of conductor insulation colours of … be exercised when connecting imported equipment that does not use AS/NZS conductor colour codes. Detailed testing should be performed to verify the function and connection of wiring …

Page 314

… is used the following conditions shall apply: (i) The terminal shall be connected by means of a protective earthing conductor to the main earthing conductor of the electrical installation … (Wiring Rules). 2 Recommendations for New Zealand are contained in the TCF Premises NZ Wiring Code of Practice . 3 Refer to Appendix F for further detail of the bonding arrangement. 5.6.3 Bonding …

Page 441

… Forum (TCF) Premises Wiring Guidelines Worksafe New Zealand NZECP 55 New Zealand Electrical Code of Practice for Managing Electrical Risks Associated with Electrically Conductive Thermal …

AS 3814:2018 Industrial and commercial gas-fired appliances 2018 cover

Name

AS 3814:2018 Industrial and commercial gas-fired appliances

Publisher

Standards Australia

Version: Seventh Edition 2018. (Current)

Specifies the uniform minimum requirements for the design, construction and safe operation of Type B appliances that are intended for use with town gas, natural gas, simulated natural gas, liquefied petroleum gas and tempered liquefied petroleum gas or any combination of these gases either together or with other fuels.

4 results

found in this document show

Page 14

… assessment techniques Metal hose assemblies Part 1-1: Guidance on the construction and use of corrugated hose assemblies Risk assessment and risk reduction—A guide to estimate, evaluate and reduce risks associated with machine tools CSA B149.6-15 Code for digester gas, landfill gas, and biogas generation and utilization Z21.21/CSA 6.5 … Functions (SIF) in Burner Management Systems (BMS) EI EI 15 3rd edition Model code of safe practice Part 15: Area classification for installations handling flammable fluids  Standards …

Page 15

… 13 AS 3814:2018 ABS 3303.0 Causes of death, Australia HSE NS-TASTGD-005 Rev. 6 ONR Guide: Guidance on the demonstration of ALARP … NIOSH IC 9458 Programmable Electronic Mining Recommendations (In Nine Parts) Systems: Best Practice UK HSE report Reducing risks, protecting people—HSE’s decision-making process NFPA 85 Boiler and Combustion Systems Hazards Code 86 Standard for Ovens and Furnaces 87 Recommended Practice for Fluid Heaters UL 429 …

Page 192

… AS 3814:2018 190 O5 NON-CONFORMANCE WITH REQUIREMENTS OF THIS STANDARD Clause 1.2.7 can be used as guidance and to assist in reviewing non-conformance … The evidence and analysis would be expected to utilize, as appropriate, recognized standards, codes of practice and industry guides where applicable. In-house procedures, specifications, guides and …

Page 194

… for purpose assessment report. The evaluation documentation would typically include sufficient of the following to establish fitness for purpose for the owner/operator and the technical … of the clause by clause assessment where there is a comparison or use of other standards, codes of practice, guides or specifications rather than using this Standard. (d) Test results of the …

AS/NZS 5601.1:2022 Gas installations, Part 1: General installations 2022 cover

Name

AS/NZS 5601.1:2022 Gas installations, Part 1: General installations

Publisher

Standards Australia/Standards New Zealand

Version: Third Edition 2022. (Current)

Sets out requirements and means of conformance for the design, installation and commissioning of gas installations that are associated with the use or intended use of fuel gases such as natural gas, LP Gas, or biogas.

Name

AS 4041-2006 Pressure piping

Publisher

Standards Australia

Version: Third Edition 2006. (Current)

Specifies minimum requirements for the materials, design, fabrication, testing, inspection, reports and pre-commissioning of piping subject to internal or external pressure.

1 results

found in this document show

Page 175

… screwed and socket-welding for the petroleum industry 3920 Derivation and verification of elevated temperature properties for steel products for pressure purposes 3974 Specification … and carbon steel ball valves for general purposes 5353 Specification for steel plug valves 5970 Code of practice for thermal insulation of pipework and equipment (in the temperature range −100°C to …

AS/NZS 5033:2021 Installation and safety requirements for photovoltaic (PV) arrays 2021 cover

Name

AS/NZS 5033:2021 Installation and safety requirements for photovoltaic (PV) arrays

Publisher

Standards Australia/Standards New Zealand

Version: Fourth Edition 2021. (Current)

Sets out general installation and safety requirements for electrical installations of PV arrays, including d.c. array wiring, electrical protection devices, switching and earthing provisions.

1 results

found in this document show

Page 59

… be to the appropriate level for the installation environment, and not less than the degree of protection IP4X. NOTE 1 This is to minimize the risks of d.c. arcs occurring between conductors and terminations. NOTE 2 Standard wiring practice should be maintained at terminations of cables to remove only the minimum insulation … important including penetrations in roofing and walls according to the relevant Standards and codes. NOTE 2 Where PV d.c. cables are installed in wiring systems near building surfaces (such …

AS/NZS 5601.2:2020 Gas installations, Part 2: LP Gas installations in caravans and boats for non-propulsive purposes 2020 cover

Name

AS/NZS 5601.2:2020 Gas installations, Part 2: LP Gas installations in caravans and boats for non-propulsive purposes

Publisher

Standards Australia/Standards New Zealand

Version: Third Edition 2020. (Current)

Specifies requirements and means of conformance for the design, installation and commissioning of LP Gas installations in caravans and boats for non-propulsive purposes.

Search all content

Sector

Publishers

Collection

State